UT Blocks

*DEFECTIVE ITEM* Alternative ASME PDI Block, A516-70 Steel [ALTASME.CS.SD7549]

Alternative ASME PDI Single Block - Alloy: A516-70 Steel - Condition: Notch in 1.000" step is 0.150" deep instead of 0.100" - 30% discount - Serial No. 7549

*DEFECTIVE ITEM* Alternative ASME PDI Block, Type 304 Stainless Steel [ALTASME.304.SD22633]

Alternative ASME PDI Single Block - Alloy: Type 304 Stainless Steel- Condition:0.500" step is undersize, out of ±0.005"- 25% Discount- Serial No. 22633

*DEFECTIVE ITEM* Alternative ASME PDI Block, Type 304 Stainless Steel [ALTASME.304.SD7532]

Alternative ASME PDI Block - Alloy: Type 304 Stainless Steel - Condition: Extra "hit" on 1.500" step, notch is 0.014" deep x0.500" long, and 0.050" from real notch- 30% discount- Serial No. 7532

*DEFECTIVE ITEM* Alternative ASME PDI Block, Type 304 Stainless Steel [ALTASME.304.SD7547]

Alternative ASME PDI Block - Alloy: Type 304 Stainless Steel- Condition: Notch in 1.000" step is 0.150" deep instead of 0.100"- 30% discount- Serial No. 7547

*DEFECTIVE ITEM* ASME Basic Cal Block, 3/4", Type 304 Stainless Steel [BASIC4.75.SS.SD]

ASME Basic Cal Block, ¾" Thick - Alloy: Type 304 Stainless Steel - Condition: Out of tolerance. 1/2T hole is drilled at0.280" from scanning surface; actual location should be0.380" 0.375" = 1/2T for nominal 3/4" thickness). Hole is located0.100"...

*DEFECTIVE ITEM* ASTM E317 Block, Figure 1, Inch, 1018 Steel [E317FIG1.ICS.SD23996]

ASTM E317 Horizontal & Vertical Linearity Block, Figure 1, Inch - Alloy: 1018 Steel, Nickel-plated- Condition: Light scratches on 2" x 3" side- 10% discount - Serial No. 23996

*DEFECTIVE ITEM* AWS Resolution Block, 1018 Steel, Nickel-Plated [AWS.CS.SD35336]

AWS Resolution Block - Alloy : 1018 Steel, Nickel-Plated.- Condition : Minor nickel-plating issue around holes on back of block. Aesthetic defect that does not affect block performance.- 10% Discount

*DEFECTIVE ITEM* AWS Resolution Block, 1018 Steel, Nickel-Plated [AWS.CS.SD40652]

AWS Resolution Block - Alloy : 1018 Steel, Nickel-Plated- Condition : Minor plating issue around hole on underside of block and Hole #5 is bell-mouthed from removal of a broken drill bit.

*DEFECTIVE ITEM* AWS Resolution Block, 1018 Steel, Nickel-Plated [AWS.SS.SD43900]

AWS Resolution Block - Alloy: 1018 Steel, Nickel-Plated- Condition: Small nick on front upper center of block. Grinding tears on back of block and customer logo laser engraved on i.- Discount: 15%- Serial Number: 43900

*DEFECTIVE ITEM* AWS Resolution Block, 7075-T6 Aluminum [AWS.A.SD]

AWS Resolution Block - Alloy: 7075-T6 Aluminum, Anodized- Condition: PH Tool logo is laser engraved partially over top of the machine engraving. Block is perfect otherwise.- 10% discount

*DEFECTIVE ITEM* AWS Resolution Block, Type 304 Stainless Steel [AWS.SS.SD]

AWS Resolution Block -Alloy: Type 304 Stainless Steel- Condition: Serial Number 45433 has 1 hole oversized in the 45° array of holes. Diameter is approximately 0.069:. Tolerance is 0.0625 +/- 0.005.Serial Number 45437 has 1 hole oversized in the...

*DEFECTIVE ITEM* BS2704-A6 Test Block [BS2704-A6.CS.SD51897]

BS2704-A6 Test Block - Alloy: 1018 Steel, Nickel-Plated- Condition: Milled slot out of tolerance on location. Should be 40mm +/- 0.125mm from right end to slot center. Actual location is 39.820mm from right end.

*DEFECTIVE ITEM* Calibration Block No. 1 (K1), 1018 Steel, Nickel-Plated [CALBLK1.CS.SD]

Calibration Block No. 1 - K1 - Alloy : 1018 Steel, Nickel-Plated- Condition : The0.080 slot has a tooling mark from the slotting cutter.- 25% Discount- Serial Nos. 40388, 40391, 40398

*DEFECTIVE ITEM* Calibration Block No. 1 (K1), 7075-T6 Aluminum, anodized [CALBLK1.A.SD37013]

Calibration Block No. 1 (K1), 7075-T6 Aluminum, anodized - Alloy: 7075-T6 Aluminum, anodized- Condition: Block Thickness is out of tolerance by0.002". Overall thickness should be 25mm 0.9842"); actual block

*DEFECTIVE ITEM* DC Block, Inch, 1018 Steel [DC.ICS.SD16716]

DC Block, Inch - Alloy: 1018 Steel, Nickel-plated- Condition: 2 minor dings on outside radius- 20% discount- Serial No. 16716

*DEFECTIVE ITEM* DC Block, Inch, 1018 Steel [DC.ICS.SD6135]

DC Block, Inch - Alloy : 1018 Steel, Nickel-Plated- Condition : Scratch on face of 2" radius.- 20% Discount- Serial No. 6135

*DEFECTIVE ITEM* DC Block, Inch, 7075-T6 Aluminum [DC.IA.SD]

DC Block, Inch - Alloy: 7075-T6 Aluminum, anodized.- Condition: Tarnished anodize from Wire EDM process- 15% discount- Serial Nos. 27293, 27294, 27295, 27296, 27298

*DEFECTIVE ITEM* DS Block, Inch, 7075-T6 Aluminum [DS.IA.SD]

DS Block, Inch - Alloy : 7075-T6 Aluminum, Anodized- Condition : Gap dimension is slightly out of tolerance at 2.0062". Gap should be 2.000" ±0.005".- 10% Discount

*DEFECTIVE ITEM* DS Test Block, Acrylic [DS.IACRY.SD]

DS Test Block - Alloy: Acrylic- Condition: Extras from a past order. Paint filled engraving.- 15% discount- Serial Nos. 6036

*DEFECTIVE ITEM* DSC Block, Inch [DSC.I7249A.SD.55965]

DSC Block, Inch - Alloy: 7249-T76511 Aluminum, Anodized- Condition: Pitting in0.125 hole- Discount: 30%Serial No: 55965

*DEFECTIVE ITEM* DSC Block, Metric, 1018 Steel [DSC.MCS.SD7865]

DSC Block, Metric - Alloy: 1018 Steel, Nickel-plated- Condition: Olympus logo, small nick on corner- 20% discount- Serial No. 7865

*DEFECTIVE ITEM* DSC Block, Metric, 1018 Steel [DSC.MCS.SD]

DSC Block, Metric - Alloy: 1018 Steel, Nickel-plated- Condition: Out of tolerance- 40% discount- Serial Nos. 23435, 23436, 23438

*DEFECTIVE ITEM* DSC Block, Metric, Type 304 Stainless Steel [DSC.MSS.SD24179]

DSC Block, Metric - Alloy: Type 304 Stainless Steel- Condition: Chipped out area in0.031" slot, roughly 1/2" long at 75mm radius.- 25% discount- Serial No. 24179

*DEFECTIVE ITEM* IIW-Type 1, Inch, 4340 Steel, Nickel-Plated [IIW1.I4340.SD41687]

IIW-Type 1, Inch - Alloy : 4340 Steel, Nickel-Plated- Condition : Block thickness is0.9927. Block should be 1.000 thick ±0.005.- 15% Discount- Serial No. 41687

*DEFECTIVE ITEM* IIW-Type 1, Metric, 1018 Steel, Nickel-Plated [IIW1.MCS.SD43015]

IIW-Type 1, Metric - Alloy: 1018 Steel, Nickel-plated- Condition: Ding on top corner of block- Discount: 10%- Serial Number: 43015

*DEFECTIVE ITEM* IIW-Type 2 Block, Inch, 7075-T6 Aluminum [IIW2.IA.SD34980]

A modified version of the original IIW-Type 1 design. Includes a 2.0" radius x0.250" deep cut-out superposed on the 4.0" radius for distance calibration. Also includes numbers 3, 5 and 8 through holes (3/64", 5/64" AND 8/64" diameter) for sensitivity...

*DEFECTIVE ITEM* IIW-Type 2 Block, Inch, 7075-T6 Aluminum [IIW2.IA.SD61054]

A modified version of the original IIW-Type 1 design. Includes a 2.0" radius x0.250" deep cut-out superposed on the 4.0" radius for distance calibration. Also includes numbers 3, 5 and 8 through holes (3/64", 5/64" AND 8/64" diameter) for sensitivity...

*DEFECTIVE ITEM* IIW-Type 2, Metric 7075-T6 Aluminum, Anodized [IIW2-M7075.SD]

IIW-Type 2, Metric - Alloy: 7075-T6 Aluminum, Anodized- Condition: Alloy is engraved on block as 7076-T6, should be 7075-T6.- 15% DiscountSerial Numbers: 22916, 22917, 22920, 22

*DEFECTIVE ITEM* IIW-Type 2, Metric, 1018 Steel [IIW2.M1018.65050.SD]

IIW-Type 2, Metric - Alloy: 1018 Steel, Nickel-plated- Condition: 1.5 dia hole out of tolerance- 25% discount- Serial Nos. 65050

*DEFECTIVE ITEM* IIW-Type 2, Metric, Type 304 Stainless Steel [IIW2.MSS.SD33333]

A modified version of the original IIW-Type 1 design in a metric version. Includes a 50mm radius x 5.0mm deep cut-out superposed on the 100mm radius for distance calibration. Also includes 1.0mm, 2.0mm and 3.0mm through holes for sensitivity testing or...

*DEFECTIVE ITEM* IOW Beam Profile Block, Metric, 1018 Steel [IOW.MCS.SD26932]

IOW Beam Profile, Metric - Alloy: 1018 Steel, Nickel-plated- Condition: Start of a hole (in wrong location) on back face.- 20% discount- Serial No. 26932

*DEFECTIVE ITEM* IOW Beam Profile Block, Metric, 7075-T6 Al [IOW.MA.SD58740]

IOW Beam Profile Block, Metric 7075 Aluminum, Anodized Alloy: 7075-T6 Aluminum, AnodizedCondition: Spot drill location off on two holes back side of block.Serial No: 58740Discount: 20%

*DEFECTIVE ITEM* Mini Angle Beam Block, Inch, 0.500" Thick, 1018 Steel [MAB.5.ICS.SD]

This miniature angle beam block is also known as a "Rompas" block or simply "Angle Beam," and it is the ASTM and U.S. Air Force substitute for the DSC block for distance, beam index, refracted angle and sensitivity calibration. Inch Contains a 1.0"...

*DEFECTIVE ITEM* Mini Angle Beam Block, Inch, 1018 Steel, NP [MAB.ICS.SD]

Mini Angle Beam Block, Inch - Alloy: 1018 Steel, Nickel-plated- Condition: S/N 33693 minor surface scratch, S/N 33698 upper left corner dented, S/N 33705 small dent on 1" radius, S/N 33713 minor surface

*DEFECTIVE ITEM* Mini Angle Beam Block, Metric, 1018 Steel, NP [MAB.MCS.SD]

Mini Angle Beam Block, Metric - Size:  25mm wide, with 25mm and 50mm radii - Alloy : 1018 Steel, Nickel-Plated - Condition : Old block with Krautkramer logo.  - 15% Discount - Serial Number:  4453

*DEFECTIVE ITEM* Mini Angle Beam Metric [MAB.MCS.SD57985/57995]

Mini Angle Beam Block, Metric - Alloy: 1018 Steel, Nickel-Plated- Condition: Last digit of Serial No "5" on both blocks is distorted- Serial No: 57985, 57995- Discount: 15%