*DEFECTIVE ITEM* Phased Array Type "A" Block (IIW-Type), 7075-T6 Aluminum [PAIIW.A.SD56216] Phased Array Type A Block, Inch - Alloy: 7075-T6 Aluminum, Anodized- Condition: Holes 25, 26, 27, 28 all0.016 deep- Serial Number: 56216- Discount: 20% Details
*DEFECTIVE ITEM* Phased Array Type "A" Block (IIW-Type), 7075-T6 Aluminum [PAIIW.A.SD50076] Phased Array Type "A" Block, Inch - Alloy : 7075-T6 Aluminum, Anodized- Condition: 45° Hole located in the 2" radius (0.078" diameter) is out of tolerance.- 20% Discount- Serial Number 50076 Details
*DEFECTIVE ITEM* PACS® Block, Metric, Type 304 Stainless Steel [PACS.MSS.SD54364] PACS® Block, Metric Alloy: Type 304 Stainless Steel- Condition: Block has discontinuity (crack) on scan surface newar 30mm holescan side- Discount: 30%- Serial Number: 54364 Details
*DEFECTIVE ITEM* PACS® Block, Metric, 1018 Steel [PACS.MCS.SD36546] PACS® Block, Metric - Alloy: 1018 Steel, Nickel-Plated- Condition: Grinding marks on flat face of block, Serial No: 36546-Hand finish grinding rolled edge, Serial No: 57512- 15% Discount- Serial No: 36546, 57512 Details
*DEFECTIVE ITEM* PACS® Block, Metric 1018 Steel [PACS.MCS.SD31178] PACS® Block, Metric - Alloy: 1018 Steel, Nickel-plated- Condition: Endmill mishap across0.500" radius 0.075" deep)- 25% discount- Serial No. 31178 Details
*DEFECTIVE ITEM* PACS® Block, 1018 Steel Nickel-Plated PACS® Block Inch - Alloy: 1018 Steel, Nickel-Plated- Condition: Ding on top scan surface- Discount: 20%-Serial Number: 51712 Details
*DEFECTIVE ITEM* PACS® Block, Inch, 1018 Steel, Nickel-Plated [PACS.ICS.SD55172] PACS® Block Inch - Alloy: 1018 Steel, Nickel-Plated- Condition: at 0.400 hole location hole tapers 0.049 @ entry and 0.045 @ exit. Broken drill removed- Discount: 20%- Serial No: 55172 Details
*DEFECTIVE ITEM* PACS® Block, Inch, 1018 Steel [PACS.ICS.SD28523] PACS® Block Inch - Alloy: 1018 Steel, Nickel-plated- Condition: Hole locations off by approx.0.010".- 20% discount- Serial No. 28523 Details
*DEFECTIVE ITEM* PACS® Block, Inch, Alloy 600 [PACS.I600.SD43683] PACS® Block Inch - Alloy: Alloy 600- Condition: Hole locations off by approx.0.006". Block width is out of tolerance. Block width should be 2.000", but actually is 1.994".- 35% discount Details
*DEFECTIVE ITEM* PACS.AWS Block, Inch 2101 Duplex SS [PACS.AWS.I2101.SD55429] PACS®, AWS Block, Inch - Alloy: 2101 Duplex Stainless Steel- Condition: Block has a slight rounded edge at 1.0 rad end- Discount: 20%- Serial No: 55429 Details
*DEFECTIVE ITEM* ASTM E2491 PA Assessment Block, Inch [PA10208.SS.SD50072] Block features: Four (4) angled holes (30°, 45°, 60°, 75°) at 1/16" 0.0625) diameter Array of 18 holes on 1" radius at0.040" diameter. Angular separation between holes is 5.0°, with 2.5° of separation between the last two holes... Details
*DEFECTIVE ITEM* ASTM E2491 PA Assessment Block, Metric [PA10208.MSS.SD52004] Block Features: Four (4) angled holes (30°, 45°, 60°, 75°) at 1/16" 0.625) diameter Array of 18 holes on 1" radius at0.040" diameter. Angular separation between holes is 5.0°, with 2.5° of separation between the last two holes... Details
*DEFECTIVE ITEM* ASTM E2491 PA Assessment Block, Metric, Type 304 SS [PA10208.MSS.SD50090,50091] Block features: Four (4) angled holes (30°, 45°, 60°, 75°) at 1.5mm diameter Array of 18 holes on 25mm radius at 1.0mm diameter. Angular separation between holes in 5.0°, with 2.5° of separation Metric Details
*DEFECTIVE ITEM* ASTM E2491 PA Assessment Block (a.k.a. Type B), Metric, Type 304 SS [PA10208.MSS.SD35123] Block features: Four (4) angled holes (30°, 45°, 60°, 75°) at 1.5mm diameter Array of 18 holes on 25mm radius at 1.0mm diameter. Angular separation between holes is 5.0°, with 2.5° of separation between the last two holes in the... Details
*DEFECTIVE ITEM* Pa Assessment Block, Metric [PA10208.MSS.SD] Block features: Four (4) angled holes (30°, 45°, 60°, 75°) at 1.5mm diameter Array of 18 holes on 25mm radius at 1.0mm diameter. Angular separation between holes is 5.0°, with 2.5° of separation between the last two holes in the... Details
*DEFECTIVE ITEM* ASTM E2491 PA Assessment Block (a.k.a. Type B), Metric, 1018 Steel [PA10208.MCS.SD30374] Block features: Four (4) angled holes (30°, 45°, 60°, 75°) at 1.5mm diameter Array of 18 holes on 25mm radius at 1.0mm diameter. Angular separation between holes is 5.0°, with 2.5° of separation between the last two holes in the... Details
*DEFECTIVE ITEM* ASTM E2491 PA Assessment Block (a.k.a. Type B), Metric, 1018 Steel [PA10208.MCS.SD30369] Block features: Four (4) angled holes (30°, 45°, 60°, 75°) at 1.5mm diameter Array of 18 holes on 25mm radius at 1.0mm diameter. Angular separation between holes is 5.0°, with 2.5° of separation between the last two holes in... Details
*DEFECTIVE ITEM* ASTM E2491 PA Assessment Block, Metric, 1018 Steel [PA10208.MCS.SD] Block features: Four (4) angled holes (30°, 45°, 60°, 75°) at 1.5mm diameter Array of 18 holes on 25mm radius at 1.0mm diameter. Angular separation between holes is 5.0°, with 2.5° of separation between the last two holes in the... Details
*DEFECTIVE ITEM* ASTM E2491 PA Assessment Block, Metric 7075-T6 Aluminum [PA10208.MAL.SD] Block features: Four (4) holes (30°, 45°, 60°, 75°) at 1.5mm diameter Array of 18 holes on 25mm radius at 1.0mm diameter. Angular separation between holes is 5.0°, with 2.5° of separation between the last two holes in the array... Details
*DEFECTIVE ITEM* Pa Assessment Block, Inch [PA10208.ICS.SD58987] Block Features: Four (4) angled holes (30°, 45°, 60°,75°) at 1/16" 0.625) diameter Array of 18 holes on 1" radius at0.040" diameter. Angular separation between holes is 5.0°, with 2.5° of separation between the last two holes in... Details
*DEFECTIVE ITEM* ASTM E2491 PA Assessment Block, Inch [PA10208.ICS.SD39153] Block features: Four (4) angled holes (30°, 45°, 60°, 75°) at 1/16" 0.0625) diameter Array of 18 holes on 1" radius at0.040" diameter. Angular separation between holes is 5.0°, with 2.5° of separation between the last two holes... Details
*DEFECTIVE ITEM* Phased Array Type "A" Block (IIW-Type), Inch, Type 304 Stainless Steel [PA.TYPA.SS.SD54181] Phased Array Type "A" Block, Inch - Alloy: Type 304 Stainless Steel- Condition: Slight mark on entry of 30° angle hole- Discount: 10%- Serial No: 54181 Details
*DEFECTIVE ITEM* Phased Array Type "A" Block, Inch, Type 304 Stainless Steel [PA.TYPA.SS.SD43771] Phased Array Type "A" Block, Inch - Alloy: Type 304 Stainless Steel- Condition: Small nicks/ding on end of block. Does not affect functionality of block.- Discount: 10%- Serial #43771<b Details
*DEFECTIVE ITEM* Phased Array Type "A" Block, Metric, Type 304 SS [PA.TYPA.SS.SD.43775] Phased Array Type "A" Block, Metric Alloy: Type 304 Stainless SteelCondition: Broken drill which has been removedDiscount: 20% Details
*DEFECTIVE ITEM* Phased Array Type "A" Block (IIW-Type), Inch, Type 304 Stainless Steel [PA.TYPA.SS.SD] Phased Array Type "A" Block, Inch - Alloy: Type 304 Stainless Steel- Condition: Serial Number 41682 #10 hole is not straight within tolerance of0.008, part exit hole should be 8.000 and it is 7.9905Serial Number 41684 #5 hole is too big due to broken... Details
*DEFECTIVE ITEM* Phased Array Type "A" Block, Metric 1018 Steel - S&D [PA.TYPA.CS.SD51047] Phased Array Type "A" Block, Metric - Alloy: 1018 Steel, Nickel-Plated- Condition: Broken drill due to power outage.0.030 wide x0.009 deep near edge of FBH #26- Discount: 20%- Serial Number: 51047 Details
*DEFECTIVE ITEM* Phased Array Type "A" Block, Metric, 1018 Steel, Nickel-Plated [PA.TYPA.CS.SD49767] Phased Array type "A" Block, Metric, 1018 Steel, Nickel-Plated - Alloy: 1018 Steel, Nickel-Plated- Condition: Hole number 14 is oversized. It is0.100 deep and0.0490 dia off center- Discount: 25%- Serial Number: 49767 Details
*DEFECTIVE ITEM* Phased Array Type "A" Block, Inch 1018 Steel, Nickel-Plated [PA.TYPA.CS.SD47158/47156] Phased Array Type "A" Block, Inch, 1018 Steel, Nickel-Plated - Alloy: 1018 Steel, Nickel-Plated- Condition: Serial number 47158: Ding on 4.00 radiusSerial number 47156: Ding on edge of 4x12 surface- Discount: 10%- Serial Numbers: 47156, 47158 Details
*DEFECTIVE ITEM* Phased Array Type "A" Block, Metric, 1018 Steel - S&D [PA.TYPA.CS.SD32828] Phased Array Type "A" Block, Metric - Alloy: 1018 Steel, Nickel-plated- Condition: 0.3mm deep EDM notch location is off center to the right by approximately 1mm, resulting in incorrect notch spacing. Details
*DEFECTIVE ITEM* Phased Array Type "A" Block, Metric, 1018 Steel - S&D [PA.TYPA.CS.SD32818] Phased Array Type "A" Block, 1018 Steel, Nickel-plated, Metric - Alloy: 1018 Steel, Nickel-plated- Condition: Out of tolerance. 45° angled hole on 50mm radius is 2.3mm diameter (should be 2.0mm). #1 Details
*DEFECTIVE ITEM* Phased Array Type "A" Block, Metric, 1018 Steel - S&D [PA.TYPA.CS.SD30488] Phased Array Type "A" Block, 1018 Steel, Metric - Alloy: 1018 Steel, Nickel-plated- Condition: 30° angled hole on 25mm radius is oversize @ 3-4mm Ø; should be 2mm Ø.- 20% Discount Details
*DEFECTIVE ITEM* Phased Array Type "A" Block, Metric 1018 Steel - S&D [PA.TYPA.CS.SD30485] Phased Array Type "A" Block, Metric - Alloy: 1018 Steel, Nickel-plated- Condition: 4mm FBH is slightly oversize @ 4.27mm 0.168")- 20% discount- Serial No. 3048 Details
*DEFECTIVE ITEM* Phased Array Type "A" Block, Inch 1018 Steel, Nickel-Plated [PA.TYPA.CS.SD] Phased Array Type "A" Block, Inch - Alloy: 1018 Steel, Nickel-Plated-Condition: Hole out of position, should be centered on 1/4" cut out. (See Below)- Serial Number: 51911 35° hole location should be0.125, actual0.16351912 35° hole location... Details
*DEFECTIVE ITEM* Phased Array Type "A" Block, Metric, 7075-T6 Aluminum - S&D [PA.TYPA.A.SD37057] Phased Array Type "A" Block, Metric - Alloy: 7075-T6 Aluminum, anodized- Condition: Block was dropped, resulting in slightly-rounded edges on top-rear corner of block, and corner of 50mm radius. Aesthetic defect. Details
*DEFECTIVE ITEM* Mini PACS® Block, Inch, Type 304 Stainless Steel [MINIPACS.SS.SD39239] Mini PACS® Block, Inch - Alloy: Type 304 Stainless Steel- Condition: Hole at location0.600 is overzsized @0.0490, should be0.0469 +/_0.001- Discount: 20%- Serial Number: 39239 Details